■M67 Adaptor for Front Port Wide
UCL-165M67" and " UCL-330" on INON "Front Port Wide" which is lens port for INON X-2 housing. Supports macro imaging by shortening the minimum focus distance of the compatible zoom lens. Rubber pressure attachment structure enables to detach easily underwater when not using the M67 Adapter.
■Weight: 61g (2.2oz) [air] / approx.39g (1.4oz) [underwater]
■Compatible Port / Lens
Front Port Wide + MRS Base Port
Panasonic LUMIX G VARIO 14-42mm/F3.5-5.6 ASPH./MEGA O.I.S
Panasonic LUMIX G VARIO 14-45mm/F3.5-5.6 ASPH./MEGA O.I.S
■Lens Monitor Hood X-2
■Compatible[X-2] series housing
X-2 for GF1 WT, X-2 for GF1 BK
■Grip Base M1
■Weight: 260g (9.2oz) [air] / approx.150g (5.3oz) [underwater]
INON X-2 for GF1, INON X-2 for GF2
Olympus PT-EP01, Olympus PT-EP03
■D Base M1
This product is equivalent to "Grip Base M1" without "D Holder" and especially suitable for existing "D Holder" owners.
■Weight: 110g (3.9oz) [air] / approx.73g (2.6oz) [underwater]
Optional D Holder to add to this product as additional strobe arm for dual strobe configuration and/or to hold whole system with both hands.
■Weight: 150g (5.3oz) [air] / approx.77g (2.7oz) [underwater]
■Grip Base D4
A universal strobe arm system fitting to more than 100 different housings without rattle.
*When using for the X-2 for GF1 / X-2 for GF2 housing, the D Holder of the Grip Base D4 is for the left hand side only. Installing on the right hand side will interfere the back of the right hand when directly holding the housing.
■Weight: 250g (8.8oz) [air] / approx.142g (5.0oz) [underwater]
■Optical D Cable Type L
Fiber optics products to connect the X-2 housing and compatible strobe via Double Optical D Connector. Four different length to choose; "Optical D Cable Type L" with free length approx. 43cm / 17in, "Optical D Cable L Type L" with free length approx. 68cm / 27in, "Optical D Cable SS Type L" with free length approx. 24cm / 9in, and "Optical D Cable LL Type L" with free length approx. 110cm / 43in .
■Holder II Set
Arm base to attach a strobe on the X-2 housing. Firmly attached on a housing by 2 x tripod screws. The holder supports back of the right hand to enhance holding strength of the housing is slidingly adjustable to suits to different hand size. INON strobe arm system is directly attached on the Holder II.
■Weight: 212g (7.5oz) [air] / approx.66g (2.3oz) [below the surface]
■Holder II Grip Set
■Weight: 410g (14.5oz) [air] /
approx.196g (6.9oz) [below the surface]
■Shoe Base Adapter X-2
■Weight: 10g (0.4oz) [air] / approx.6g (0.2oz) [underwater]
■Compatible [X-2] series housing
X-2 for EOS10D, X-2 for EOS10D BK, X-2 for EOS20D, X-2 for EOS20D BK
X-2 for EOS20D BK(TM), X-2 for EOS30D BK(TM), X-2 for EOS50D/40D,
X-2 for GF1 WT, X-2 for GF1 BK
■Compatible arm system products
Grip+Bar III Set, Holder II Grip Set, Holder Base, Grip Bar Set, Grip Bar II Set
*The thumbscrew of the "Z Joint" or "Light Holder" could possibly obstruct free movement of an Optical D Cable product or electrical cable attached on X-2 housing series.
■Front Port Rear Cap
Front Port Macro, Front Port Wide, Front Port Dome 115, Front Port Flat 5
■MF Rear Port Cap
■Dome Port Cover
■Dome Port Cover S
The Dome Port Cover S is made of neoprene as same as wet suits. It is recommended to cover Dome Port 115 or Front Port Dome 115 with this cover until just before you use to prevent accidental damage. The Dome Port Cover S has slits on its top and bottom to help easy and speedy installation/removal on a dome lens/port equipped with a hood.
Dome Port 115, Front Port Dome 115
■Compatible Attachment Lens
Dome Lens Unit II for UWL-H100, Dome Lens Unit II for UWL-100,
Dome Lens Unit for UWL-100
*Never put wet lens cover on compatible lens/port on land. Doing so may cause degradation of the lens coating or glass itself resulting in spotting or discoloration.
■Front Port Cover 100
■Snap-on Lens Cap M67
■Shade Sponge D60
■Shade Ring 46
■Comaptible Port / Lens
Panasonic LUMIX G 14mm/F2.5 ASPH.
■MRS Control Ring (MRS60/60UII/100UII/100UIII/50 for Olympus)
Optional MRS Control Ring to upgrade a port without "MRS Control Ring" to full MRS system which utilizes magnetic attraction to rotate a lens barrel for manual focusing like as land operation of a camera.
■Weight: 129g (4.6oz) [air] / 47g (1.7oz) [underwater]
MRS60 Port II (w/o control ring)
MRS60 Port (w/o control ring)
MRS100 Port Type UII (w/o control ring)
MRS100 Port Type UIII (w/o control ring)
MRS50 Port (w/o control ring) for Olympus
MRS Base Port (w/o control ring)
■Protector for Dome Lens Unit II/Dome Port 115/Front Port Dome 115
■X-2 Main O-ring 175 for 10D/20D/30D/50D40D/60D/70D/6D/GF1/GF2
Spare oil-bearing INON yellow O-Ring for housing body.
X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D
X-2 for EOS50D/40D
X-2 for GF1, X-2 for GF2
■O-ring for Port / Extension Ring
Spare oil-bearing INON yellow O-Ring for Port or Extension Ring.
■Compatible Port / Extension Ring
Dome Port II, MRS60 Port II, MRS60 Port, MRS100 Port Type UIII,
MRS 100Port Type UII, MRS 100Port Type S, MF Wide Port, MF Flat Port,
MF Standard Port 2
Dome Port 115, Pancake Port, MRS Base Port
Extension Ring S, Extension Ring M, Extension Ring L, Extension Ring 18,
Extension Ring 36, Extension Ring 58, Extension Ring 81, MF EXT. Ring M
■O-ring for MRS Front Port
Spare oil-bearing INON yellow O-Ring for MRS Front port.
Front Port Macro, Front Port Wide, Front Port Dome 115
Grease exclusively for oil bearing INON yellow O-ring.
■Corrosion Suppression Unit
Optional replacement unit when pre-installed unit gets worn. The unit suppresses housing corrosion by oxidizing before the X-2 housing body gets rusted.