INON

X-2 Lanyard Plate R

JAN code : 4562121439665

 
X-2 Lanyard Plate R
 
Set-up image

Set-up image

 
Set-up image

Set-up image

Enables to attach a lanyard on INON X-2 for EOS6D, X-2 for EOS70D or X-2 for EOS80D VC.Arc-like elongate slots allow to adjust orientation of eyelets.The plate can accommodate with wide range of housing adapters.Packaged grommets can contribute to avoid annoying rattle sounds when filming movie as well as not to damage on a housing by metal rings of the lanyard.
 
 
Weight: [air] 52 g/1.8 oz. [underwater] approx.42 g/1.5 oz. 
 
Compatible X-2 series Housing (*1)
X-2 for EOS6D, X-2 for EOS70D, X-2 for EOS80D VC

 
Compatible Arm System Products (*2)
Multi Direct Base IIa
Multi Direct Base II WB
Multi Direct Base II Long
Shoe Base Adapter X-2 + Shoe Base II
M6 Plate Direct Base III+ Direct Base III
M6 Plate Direct Base III+ Direct Base YS RT

 

(*1) It is possible to attach this product to X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D, X-2 for EOS50D/40D or X-2 for EOS60D but it requires to remove pre-installed "Lanyard hook". Please consult with your purchasing dealer. Not compatible with an INON housing which has done "Sync Connector Installation".
(*2) Attaching Clamp III, Z Joint or Light Holder products may interfere full movement of the lanyard. 

page top

Optical D Cable Type L

Optical D Cable Type L

Fiber optics products to connect the X-2 housing and compatible strobe via Double Optical D Connector. Four different lengths are available; Optical D Cable Type L with free length approx. 43 cm/17 in, Optical D Cable L Type L with free length approx. 68 cm/27 in, Optical D Cable SS Type L with free length approx. 24 cm/9 in, and Optical D Cable LL Type L with free length approx. 110 cm/43 in.
 
 

page top

X-2 Holder III Spacer

JAN code: 4562121439191

X-2 Holder II Spacer

A spacer designed to attach the Holder III directly on the right side of the INON X-2 housing to benefit with less weight if left hand grip is not required. INON Arm System is directly attachable on the top end of the Holder III.
 
Weight[air] 48 g/1.7 oz. [underwater] approx.31 g/1.1oz  *standalone
              [air] 236 g/8.3 oz. [underwater] approx.79 g/2.8 oz  *with Holder III

 
Set-up image

Set-up image

page top

Main Base III

JAN code:4562121439160

 
MainBaseIII
 

A base plate attached on the bottom of an underwater housing to add a handle. As pre-installed two tripod screws are adjustable within center-to-center distance 33-105mm/1.3-4.1inch, it widely supports from compact housing to large SLR housing enabling you to use the same base plate when you change camera system.
 
Weight: [air]134 g/4.7 oz. [underwater] approx.82 g/2.9 oz.

Holder III

JAN code:4562121439177

HolderIII
 

When holding an underwater housing directly by hand, the Holder III supports the back of your hand. The top end is designed to attach wide range of INON Arm System products.
 
Weight: [air] 156 g/5.5 oz. [underwater] approx.80 g/2.8 oz.

Holder III Set

JAN code:4562121439184

HolderIIISet

Unlike previous Holder II, the Holder III can be attached on both sides of an underwater housing and top end has total four fixing screw holes comparing to two of Holder II. The Holder III can be installed with three different angles (Holder III attached on the Main Base III at the right angle may interrupt proper opening/closure of combined underwater housing. If this happens, remove the Main Base III with Holder III(s) from the housing to open/close the housing.) Compatible with the Panhead Adapter packaged with the UW 3-Way Panhead.
 
 
Weight: [air] 290 g/10.2 oz. [underwater] approx.162 g/5.7 oz.
 
 

page top

Shoe Base Adapter X-2

JAN code : 4562121435667

click to enlarge
 
click to enlarge

Set-up image


An adapter to attach the Shoe Base on top of the X-2 series housing or Grip Bar III Set enabling to hold Z-330/D-200/S-2000/Z-240/D-2000 strobe or LE series LED flashlight combined with Z Joint or Light Holder product to have compact yet flexible lighting.
 
Weight: [air]10 g/0.4 oz. [underwater] approx. 6 g/0.2 oz.
 
Compatible [X-2] series Housing
X-2 for EOS10D, X-2 for EOS10D BK, X-2 for EOS20D, X-2 for EOS20D BK
X-2 for EOS20D BK(TM), X-2 for EOS30D BK(TM), X-2 for EOS50D/40D
X-2 for EOS60D, X-2 for EOS70D, X-2 for EOS6D, X-2 for EOS80D VC,
X-2 for GF1, X-2 for GF2
 
Compatible Arm System Products
Grip Bar III Set, Holder II Grip Set, Holder Base, Grip Bar Set, Grip Bar II Set
 

*The thumbscrew of the Z Joint or Light Holder could possibly obstruct free movement of an Optical D Cable product or electrical cable attached on X-2 housing series.

page top

Straight Viewfinder Unit II for X-2

JAN code : 4562121439207

STVF Unit II for X-2
  
Simulated viewfinder image when using for X-2 for EOS6D

Simulated viewfinder image when using for X-2 for EOS6D

 
Compact and lightweight straight type viewfinder supporting full frame DSLR.Using a large prism to minimize light attenuation makes it possible to see every corner of camera’s viewfinder image clearer and brighter despite of eye position.Unlike conventional viewfinders, this bright viewfinder enables you to focus precisely and comfortably even in dark underwater. Optically designed to suit to an electrical viewfinder (EVF) of a DSLR camera which provides wider viewing angle, so no vignetting nor blur even in corners.Magnification of this viewfinder is same as camera’s viewfinder. As its eye-point underwater is extended to 60 mm/2.4 inch, no vignetting of viewfinder image even through a mask.Viewfinder body is made from corrosion resistant aluminum and fiber reinforced plastic (FRP) to make the body compact, lightweight yet durable.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air]305 g/10.7 oz. 

45º View Finder Unit II for X-2

 JAN code : 4562121439306

click to enlarge

 

45° View Finder

Simulated viewfinder image (X-2 for EOS6D)

The 45°Viewfinder is an interchangeable finder unit to extend eye-point of camera's viewfinder without changing image size (x1.0) to see almost all finder image and display on the camera’s viewfinder even through a mask. The eye piece is at 45 degree angle to camera's optical axis which helps to shoot lower subject like a goby on seabed. Also the eye piece is 360 degree rotatable making it easy to shoot vertical composition from low angle.
 
*Finder corners may get slightly dark.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 337 g/11.9 oz.

---Tips on diopter adjustment ---
Under bright circumstance on land, human eye’s pupil shrinks making diopter adjustment easy as depth of field is deep while the adjusted viewfinder may not provide perfect focus and it becomes hard to see viewfinder image when the pupil gets open in dark underwater as the depth of field gets shallow especially with presbyopic eyes due to deteriorated focusing function (Though it varies among different individuals or ages, it takes about 15 minutes to open pupils by dark adaptation when we get dark underwater).

So it would be recommended to conduct diopter adjustment in a dark room (darker than underwater) after staying there 15 minutes  when pupils open as like being underwater to get perfect focus of viewfinder image even underwater where pupils will open.

 Diopter Correction Lens (+1.5D) for 45VF-II/STVF-II

 JAN code : 4562121439313 

 
Diopter Correction Lens [+1.5D] for STVF-II

Optional accessory for Straight Viewfinder Unit II for X-2 and 45º View Finder Unit II for X-2.Add-on correction lens to shift +1.5 diopter for those who are unable to adjust with camera’s viewfinder diopter adjustment range due to long sight or presbyopia.The Diopter Correction Lens is to be installed before diving by dropping it inside of the Straight Viewfinder Unit II from housing side and tighten it by packaged tool (not changeable underwater).
 
Weight[air] 2 g/0.07 oz. 

Straight View Finder Unit for X-2

[Discontinued]

click to enlarge

 

Straight View Finder

Simulated viewfinder image (X-2 for EOS6D)

The Straight Viewfinder Unit for X-2 is an interchangeable finder unit to extend eye-point of camera's viewfinder without changing image size (x1.0) to see almost all finder image area even through a mask. The eye piece is level to camera's optical axis to position camera/housing closer to a subject without changing your position.
 
*As the Straight Viewfinder is originally designed for APS-C format, using for a full frame camera will have blind section on the center of the upper edge and either left or right edge may have slight blind section as well.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 277 g/9.8 oz. 

Pick-up Finder Unit 3 for X-2

JAN code : 4562121438057

click to enlarge

 

Pick-up Finder Unit 3

Simulated viewfinder image (X-2 for EOS6D)

The Pick-up Finder Unit 3 for X-2 is a compact interchangeable finder unit to extend eyepoint and scale down image size (x0.75) to practically suppress vignetting to check composition even through a mask.
Previous Pick-up Finder Unit for X-2 is not usable for EOS 6D but possible to use in combination with optional Pick-up Finder Unit 3 (camera side module).
 
*Existing Pick-up Finder Unit for X-2/Pick-up Finder Unit 2 for X-2 users can use as Pick-up Finder Unit 3 for X-2 by replacing original Pick-up Finder Unit (camera side module)/Pick-up Finder Unit 2 (camera side module) with optional Pick-up Finder Unit 3 (camera side module). Please contact your INON dealer for detail.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 34 g/1.2 oz. 

Pick-up Finder Unit 3 (camera side module)

Pick-up Finder Unit 3 (camera side module)

 

Pick-up Finder Unit 3 (camera side module) Set-up image

Set-up image

A module for camera's viewfinder.
Existing Pick-up Finder Unit for X-2/Pick-up Finder Unit 2 for X-2 users can use as Pick-up Finder unit 3 for X-2 by replacing original Pick-up Finder Unit (camera side module)/Pick-up Finder Unit 2 (camera side module) with optional Pick-up Finder Unit 3 (camera side module).
 
*Pick-up Finder Unit 3 for X-2 comes with this module.
 
 

Finder Window Unit for X-2

JAN code : 4562121432949

click to enlarge

 

Finder Window

Simulated viewfinder image (X-2 for EOS6D)

The Finder Window Unit for X-2 is most inexpensive interchangeable finder unit which consists of single waterproof window made of optical glass to access camera's finder. This unit does not have optical function like extending camera's eye-point so only center part of camera's finder is visible through a mask.
 
*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included when purchasing this product only.
 
Weight: [air] 27 g/1.0 oz. 

Lock Ring Tool for X-2 Housing

Lock Ring Tool for X-2 Housing

Dedicated tool (same as packaged tool with an INON X-2 housing) to use when installing/removing a finder unit.
When purchasing finder unit product only, the Lock Ring Tool for X-2 Housing is not included.

page top

MF Rear Port Cap

JAN code : 4562121430389

MF Rear Port Cap

A rear cap for an INON port. When transporting or during storage, this cap protects O-ring and screw mount. The cap is designed to equalize with ambient pressure when transporting in an aircraft.
 

Usage example

Usage example

Housing Body Cap

JAN code : 4562121430136

Housing Body Cap

A cap for port mount of a housing to protect O-ring contact surface. The cap is designed to equalize with ambient pressure when transporting in an aircraft.
 

Usage example

Usage example

page top

X-2 Main O-ring 175 for 10D/20D/30D/50D40D/60D/70D/6D/GF1/GF2

Main O-Ring for X-2 Housing Body

Spare oil-bearing INON yellow O-ring for housing body.
 
Comaptible Housing
X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D
X-2 for EOS50D/40D, X-2 for EOS60D, X-2 for EOS70D, X-2 for EOS6D
X-2 for GF1, X-2 for GF2

O-ring for Port/Extension Ring

O-Ring for Port / Extension Ring

Spare oil-bearing INON yellow O-ring for port or Extension Ring.
 
Compatible Port/Extension Ring
Dome Port 2, MRS60 Port II, MRS60 Port, MRS100 Port Type UIII,
MRS100 Port Type UII, MRS100 Port Type S, MF Wide Port, MF Flat Port,
MF Standard Port 2
Dome Port 115, Pancake Port, MRS Base Port
Extension Ring S, Extension Ring M, Extension Ring L, Extension Ring 18, Extension Ring 36, Extension Ring 58, Extension Ring 81, MF EXT. Ring M

INON Grease

INON Grease

Grease exclusively for oil bearing INON yellow O-ring.

Finder Unit Fixing Screw Ring [service part]

Finder Unit Fixing Screw Ring

Dedicated nut to fix a finder unit product on an INON X-2 housing. (same as packaged screw ring with an INON X-2 housing)
 
When purchasing finder unit product only, the Finder Unit Fixing Screw Ring is not included.

Battery Tray 2xCR2032 [service part]

Battery Tray 2xCR2032

A tray to hold two CR2032 battery cells in a battery holder of the Leak Sensor/Optical Flash Trigger.

Corrosion Suppression Unit

Corrosion Suppression Unit

Optional replacement unit when pre-installed unit gets worn. The unit suppresses housing corrosion by oxidizing before the X-2 housing body gets rusted.
 
 

page top