INON

■X-2 Lanyard Plate

X-2 Lanyard Plate

Set-up imageSet-up imageAttaching this plate on INON X-2 for EOS6D or X-2 for EOS70D housing utilizes to use commercially available lanyard (carry belt).
The plate is attached on the "Base Adapter Fixing Screw Hole (M6)" of the compatible housing by screws or by compatible INON arm adapter.
Supplied rubber grommet prevents uncomfortable clinking noise between this product and metal hook from recording when shooting video as well as scratching the housing body.

Set-up imageSet-up image■Weight: 52g (1.8oz) [air] / approx.42g (1.5oz) [underwater]

■Compatible [X-2] series Housing (*1)
X-2 for EOS6D, X-2 for EOS70D

■Compatible arm system products (*2)
Multi Direct Base IIa
Multi Direct Base II WB
Multi Direct Base II Long
Shoe Base Adapter X-2 + Shoe Base
M6 Plate Direct Base III+ Direct Base III
M6 Plate Direct Base III+ Direct Base YS RT

(*1) It is possible to attach this product to X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D, X-2 for EOS50D/40D or X-2 for EOS60D but it requires to remove pre-installed "Lanyard hook". Please consult with your purchasing dealer. Not compatible with an INON housing which has done "Sync Connector Installation".
(*2) Attaching "ClampⅢ", "Z Joint" or "Light Holder products" may interfere full movement of the lanyard.

clear.png

clear.png

A spring snap hook installed on the X-2 Lanyard Plate (with grommet)A spring snap hook installed on the X-2 Lanyard Plate (with grommet)

A split ring installed on the X-2 Lanyard PlateA split ring installed on the X-2 Lanyard Plate

X-2LanyardPlate_rope.jpgA carrying rope attached on the X-2 Lanyard Plate

Optical D Cable Type L

Fiber optics products to connect the X-2 housing and compatible strobe via Double Optical D Connector. Four different length to choose; "Optical D Cable Type L" with free length approx. 43cm / 17in, "Optical D Cable L Type L" with free length approx. 68cm / 27in, "Optical D Cable SS Type L" with free length approx. 24cm / 9in, and "Optical D Cable LL Type L" with free length approx. 110cm / 43in.

LinkIconLearn more

■Holder II Grip Set

Holder II Grip Set

A base stay with grip for a SLR housing to attach a strobe etc. The Holder II Grip Set is firmly attached on a housing by two tripod screws. The padded Holder supports back of right hand which holds the housing directly and the Grip on the left is designed to access to focus/zoom dial by left fingers with holding it. Both of them are adjustable to accommodate to a variety of hand sizes.

■Weight: 410g (14.5oz) [air] / approx.196g (6.9oz) [below the surface]

■X-2 Holder II Spacer

click to enlarge

Set-up imageSet-up imageA spacer designed to attach the Holder II directly on the right side of the INON X-2 housing to benefit with less weight if left hand grip is not required. INON Arm System is directly attachable on the top end of the Holder II.

■Weight: 34g (1.2oz) [air] / approx.21g (0.7oz) [underwater] *standalone
159g (5.6oz) [air] / approx.13g (0.5oz) [under surface] *with Holder II

■Shoe Base Adapter X-2

click to enlarge

click to enlargeSet-up imageAn adapter to attach the Shoe Base on top of the X-2 series housing enabling to hold Z-240/D-2000/S-2000 strobe or LE series LED flashlight combined with Z Joint or Light Holder product.

■Weight: 10g (0.4oz) [air] / approx.6g (0.2oz) [underwater]

■Compatible [X-2] series Housing
X-2 for EOS10D, X-2 for EOS10D BK, X-2 for EOS20D, X-2 for EOS20D BK
X-2 for EOS20D BK(TM), X-2 for EOS30D BK(TM), X-2 for EOS50D/40D
X-2 for EOS60D, X-2 for EOS70D

■Compatible arm system products
Grip+Bar III Set, Holder II Grip Set, Holder Base, Grip Bar Set, Grip Bar II Set

*The thumbscrew of the "Z Joint" or "Light Holder" could possibly obstruct free movement of an Optical D Cable product or electrical cable attached on X-2 housing series.

■MF Rear Port Cap

MF Rear Port Cap

Set-up imageSet-up imageA rear cap for a port (except for Front Port) and Extension Ring. When transporting or during storage, this cap protects O-ring and screw mount. The cap is designed to equalize with ambient pressure when transporting in an aircraft.

■Housing Body Cap

Housing Body Cap

Set-up imageSet-up imageA cap for port mount of a housing to protect O-ring contact surface. The cap is designed to equalize with ambient pressure when transporting in an aircraft.

■Main O-Ring for X-2 Housing Body

Main O-Ring for X-2 Housing Body

Spare oil-bearing INON yellow O-Ring for housing body.

■Comaptible Housing
X-2 for EOS10D, X-2 for EOS20D, X-2 for EOS30D
X-2 for EOS50D/40D, X-2 for EOS60D, X-2 for EOS70D, X-2 for EOS6D
X-2 for GF1, X-2 for GF2

■O-Ring for Port / Extension Ring

O-Ring for Port / Extension Ring

Spare oil-bearing INON yellow O-Ring for port or Extension Ring.

■Compatible Port / Extension Ring
Dome Port 2, MRS60 Port II, MRS60 Port, MRS100 Port Type UIII,
MRS100 Port Type UII, MRS100 Port Type S, MF Wide Port, MF Flat Port,
MF Standard Port 2
Dome Port 115, Pancake Port, MRS Base Port
Extension Ring S, Extension Ring M, Extension Ring L, Extension Ring 18, Extension Ring 36, Extension Ring 58, Extension Ring 81, MF EXT. Ring M

■INON Grease

INON Grease

Grease exclusively for oil bearing INON yellow O-Ring.

45° View Finder Unit for X-2

click to enlarge

45°View Finder Unit for X-2Simulated viewfinder image (X-2 for EOS70D)
The 45° Viewfinder is an interchangeable finder unit to extend eye-point of camera's viewfinder without changing image size (x1.0) to see all finder image area even through a mask without vignetting. The eye piece is at 45 degree angle to camera's optical axis which helps to shoot lower subject like a goby on seabed. Also the eye piece is 360 degree rotatable making it easy to shoot vertical composition from low angle.

*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included.

■Weight: 337g (11.9oz) [air including Finder Unit Fixing Screw Ring]

■Straight View Finder Unit for X-2

click to enlarge

Straight View Finder Unit for X-2Simulated viewfinder image (X-2 for EOS70D)
The Straight Viewfinder is an interchangeable finder unit to extend eyepoint of camera's viewfinder without changing image size (x1.0) to see all finder image area even through a mask without vignetting.
The eye piece is level to camera's optical axis to position camera/housing closer to a subject without changing your position.

*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included.

■Weight: 277g (9.8oz) [air including Finder Unit Fixing Screw Ring]

■Pick-up Finder Unit 2 for X-2

click to enlarge

Pick-up Finder Unit for X-2Simulated viewfinder image (X-2 for EOS70D)
The Pick-up Finder is a compact interchangeable finder unit to extend eyepoint and scale down image size (x0.75) to practically suppress vignetting to check composition even through a mask.
Previous "Pick-up Finder Unit for X-2" is not usable for EOS 70D but possible to use in combination with optional "Pick-up Finder Unit 2 (camera side module)".

*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included.

■Weight: 34g (1.2oz) [air including Finder Unit Fixing Screw Ring]

■Finder Window Unit for X-2

click to enlarge

Finder WindowSimulated viewfinder image (X-2 for EOS70D)
The Finder Window is most inexpensive interchangeable finder unit which consists of single waterproof window made of optical glass to access camera's finder. This unit does not have carry optical function like extending camera's eyepoint so only center part of camera's finder is visible through a mask.

*The Lock Ring Tool for X-2 Housing and Finder Unit Fixing Screw Ring is not included.

■Weight: 27g (1.0oz) [air including Finder Unit Fixing Screw Ring]

■Lock Ring Tool for X-2 Housing

Lock Ring Tool for X-2 Housing

Dedicated tool (same as packaged tool) to use when installing / removing a viewfinder unit.

*The Lock Ring Tool for X-2 Housing does not come with a viewfinder when purchasing the viewfinder standalone.

■Finder Unit Fixing Screw Ring [service part]

Finder Unit Fixing Screw Ring

Dedicated nut to fix a finder unit on a housing. (same as packaged screw ring)

*The Finder Unit Fixing Screw Ring comes with an X-2 housing but does not come with a viewfinder when purchasing the viewfinder standalone.

■Corrosion Suppression Unit

Corrosion Suppression Unit

Optional replacement unit when pre-installed unit gets worn. The unit suppresses housing corrosion by oxidizing before the X-2 housing body gets rusted.